Slide Armor 2500 Color Coat

  • Sale
  • Regular price


Aliphatic Polyurethane Color Finish. Slide Armor Color Coat is designed as the color coat and provides outstanding color, gloss and abrasion resistance.





SLIDE ARMOR vs Competitors

Properties Standar Acrylic
Polyurethane
Gelcoat
Finish
Slide Armor:
2500 Only
Slide Armor
2500 and Clear Topcoat
Water Immersion -- + ++ ++
Chemical Resistant
- + ++ ++
Abrasion Resistant + - ++ ++
UV Chalk Resistant + -- ++ +++
Color Retentive + -- ++ +++
Service Life (years) Not Recommended
in Immersion
2 5+ 7+

Colors

Application Instructions

POLY TEK CP 2500 / 2505

WATERSLIDE PREP GUIDELINES 

Depending on the condition of your waterslide project, a thorough and complete preparation process is required to assure maximum bond and long term performance.

If waxes or polishes were used on the waterslide, extra preparation is necessary to prevent adhesion failure of the coating system.

Follow the complete 10 Step process if waxes or polishes were used during the lifetime of the slide.

If no waxes or polishes were applied, follow Steps 5 – 10 only 

Step 1:        Slide Evaluation

Examine the surface condition of the slide, especially if waxes or polishes were applied.

Wax/Polished Waterslide                Steps 2 -10

Wax/Polish Free Waterslide   Steps 5 – 10

Step II         Power Wash Slide

Use 3500 psi (minimum) power washer with simple green #         to remove oil, dust,

Etc. Keep power washer wand at a close proximity to slide surface.

 

Step III        DeWax Slide

Using Zep Wax Remover at high concentration, apply directly with a soft plastic bristle

brush. Scrub wax off applying wax remover heavily to assure wax is totally removed.

 

Step IV        Power Wash Slide

Using 3500 psi (minimum) power washer using Simple Green to completely remove any waxy residue from the slide surface. Keep power washer at close proximity to slide surface.

Step V         Final Power Wash

Using 3500 psi (minimum) power washer with water only, wash all remaining detergents and wax remover from surface. Keep power washer wand in close proximity to slide surface.

Step VI        Sand/Scuff Surface

Using 220-400 grit D.A. Sander, scuff surface and remove and loose or flaking gel- coat. Entire surface of slide must be completely sanded to assure maximum bond and long term performance.

Step VII       Power Wash Slide

Using 3500 psi power washer (minimum) with water only, completely remove any dust and contamination from the sanding process. Keep power washer wand in close proximity of slide surface.

Step VIII      Repairs/Final Inspection

Repair only deep scratches, gouges or defects with standard slide repair procedures. (Bondo may be used)

Step IX       Ready to Paint

Assure slide is completely dry and free of any surface contaminants that have appeared. (dust/leavers/droppings) Blow off areas to coat prior to spraying or rolling with dry, compressed air.

What you will need:

 

  • 3500 psi pressure washer (minimum)
  • Zep stripper
  • Simple Green
  • 220 grit sandpaper / D.A. Sander
  • Plastic Bristle Scrub Brush
  • Bondo Polyester Filler

 



Specification

There are two options with the SLIDE ARMOR system The main version is SYSTEM ONE- The application of thte SLIDE ARMOR COLOR COAT. This system provide excellent color retention in harsh UV and Chlorinated pool water.
SYSTEM TWO is the combination of the SLIDE ARMOR COLOR COAT and CLEAR TOPCOAT. The CLEAR TOPCOAT provides a super high gloss "wet look" and extended properties






SLIDE ARMOR

SYSTEM ONE -POLYURETHANE COLOR COAT SYSTEM
SYSTEM TWO -POLYURETHANE COLOR COAT SYSTEM/ CLEAR TOPCOAT SYSTEM
Liquid error (layout/theme line 585): Could not find asset snippets/scm-bannerslider.liquid